Outdoor dual PIR motion detector
This detector is a component of the JABLOTRON system. The JA-169P dual wireless outdoor intruder detector is designed to detect human body movement in an outdoor environment. The detector consists of JL01 detector produced by LINCE Italia S.r.l., and a JA-150TX-V1 transmitter produced by JABLOTRON ALARMS.
The detector should be installed by a trained technician with a valid certificate issued by an authorised distributor.
Installation
Procedure:
- Unscrew the locking screw (2) on the bottom of the upper cover of the detector and remove the detection part’s cover (3).
- Unscrew all screws (1) which hold the detector´s main board (5) to its mounting plate (7) and pull it out by tilting as you pull it out. There is a radio transmitter fitted onto the rear side of the detector´s PCB.
- The detector can be mounted onto a level mounting place by the 4 screws through the mounting plate. Or it can be mounted on a pole by metal ties (not supplied).
 |
Warning: Do not touch the detector sensors during handling. In case that physical contact does occur, it´s necessary to clean the sensor with the use of a cotton swab dipped in rubbing alcohol. |
Figure 1: Description of the internal and external parts of the product
1 – bracket screws; 2 – locking screw; 3 – front cover; 4 – adjustment knob for lower PIR (PIR2); 5 – PCB holder; 6 – tamper contact; 7 – mounting backplate;
1 – bracket screws; 2 – locking screw; 3 – front cover; 4 – adjustment knob for lower PIR (PIR2); 5 – PCB holder; 6 – tamper contact; 7 – mounting backplate;
Enrolling the detector to the system
According to the type of control panel use recommended software or application – see control panel manual.
Technical specifications JA-150TX-V1
| Power | 1x Lithium battery type CR123A (3.0 V/1.4 Ah) Please note: Batteries are not included |
|---|---|
| Current consumption (quiescent/maximal) | 30 µA/55 mA |
| Typical lifetime of battery | approx. 3 years |
| Communication band | 868.1 MHz, protocol JABLOTRON |
| RF range | up to 300 m (open area) |
| Maximal radiofrequency power (ERP) | <25 mW |
| Operational environment | indoor general |
| Operating temperature range | -10 °C to +40 °C |
| Average operating humidity | 75%, non-condensing |
| Dimensions | 28 x 111 x 20 mm |
| Weight (w/o battery) | 120 g |
| Can be operated according to | ERC REC 70-03 |
Technical specifications JL01
| Power | supply using JA-150TX-V1 |
|---|---|
| Operational environment | outdoor general |
| Operating temperature range | -25 °C to +60 °C |
| Average operating humidity | 75%, non-condensing |
| Recommended installation height above the floor | 120 cm |
| Detection angle/detection coverage | 85 °/3–15 m |
| Dimensions | 188 x 81 x 98 mm |
| Weight (w/o battery) | 377 g |
  | JABLOTRON ALARMS a.s. hereby declares that the detetor JA-169P, consisting of a JL01 detector with a JA-150TX-V1 transmitter, is in a compliance with the relevant Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – Technical Section Downloads. | |
 | Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point. | |
| JA-169P | MMY58706 (27.6.2024) |
|---|