Wireless combined PIR and MW motion detector

The product is a component of the JABLOTRON system. It is used for spatial detection of movement of people in the interior of buildings. The combination of PIR and MW makes the detector highly resistant to false alarms. It uses a PIR sensor to detect the movement of people, which is then confirmed by a MW sensor. An alarm is only triggered after both sensors have been activated. The detector is designed to be installed by a trained technician with a valid Jablotron certificate.

Installation

During the installation pay attention that there should be no obstacles in the detector’s view, such as:

• items that change temperature quickly (electric stove, gas appliances etc.)
• objects that move (e.g. waving curtains over the heating, robotic vacuum cleaner)
• no obstacles obstructing the view of the protected area
• moving pets

We do not recommend installing the detector:

• against windows or spotlights
• in places where air flows (ventilation, air conditioning, vents, leaky doors etc.)
• close to metal objects (influence of microwave field)

Note: It is not possible to install two or more detectors in an area where MW transmitters could interfere with each other.

1. Open the cover of detector by using the cover latch (13). Do not touch the PIR sensor inside (6) – could be damaged.
2. Release the PCB located in the rear housing part by pressing the latch (9) at the bottom of the cover.
3. Screw the rear housing part to the wall (vertically, cover latch down). For proper detection of the detector being torn off the surface, use the tear holes in the oval part of the rear housing part to screw it in as well.
4. Insert the PCB back and lock with the latch (9). Insert batteries to the battery holder (1). Make sure the batteries are inserted with the correct polarity. Close the detector cover, snap into the cover latch (13) and lock with the locking screw (12).

Figure 1: Description of internal and external parts of the product
1 – battery holders; 2 – MW sensor; 3 – The JA-191PL external tamper connector; 4 – LED; 5 – production code; 6 – PIR sensor; 7 – tamper contact; 8 – antenna; 9 – PCB latch; 10 – light guide; 11 – PIR detector lens; 12 – arresting screw hole; 13 – cover latch;

Enrolment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specification

Power	2x lithium battery, type CR123A (3 V / 1.5 Ah) Please note: Batteries are not included.
LowBatt state	<2,7 V
Typical lifetime of batteries	approx. 4 years
Quiescent current consumption	65 μA
Maximal current consumption	50 mA
Communication frequency	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	<25 mW
Recommanded installation height	2.5 m
Detection angle / detection coverage (PIR)	110 ° / 12 m
Detection angle / detection coverage (MW)	90 ° / 12 m
Operating frequency MW	24.125 GHz
Maximum effective radiated power MW (EIRP)	30 mW
Dimensions	63 x 150 x 40 mm
Weight (without batteries)	125 g
Classification	security grade 2 / environmental class II (according to EN 50131-1)
Environment	indoor general
Operating temperature range	-10 °C to +40 °C
Average operating range	75% RH, non-condensation
Certification body	Trezor Test s.r.o. (no. 3025)
In compliance with	EN IEC 63000, EN 50130-4, EN 55032, EN 50131-1, -2-4, -5-3, -6, EN IEC 62368-1, EN ETSI 300 220-1, -2, EN ETSI 300 440
Can be operated according to	ERC REC 70-03
MW Frequency band according to ERC REC 70-03	band m)
ITU designation for MW	P0N
ITU designation for SRD	80K0F1DAN
Recommanded screw	2x ø 3.5 x 40 mm (countersunk head)
We recommend that you familiarize yourself with the terms and conditions set by local telecommunications authorities.
This detector must not be used in Great Britain as the frequency 24.05-24.15 GHz in this frequency band is allocated for police speed meters. In France, no restrictions for fixed installations, otherwise limited to 0.1 mW e.i.r.p. in 24.10-24.15 GHz. In Russia, fixed installations are permitted with a maximum of 100 mW e.i.r.p., subject to specific installation requirements.

	JABLOTRON a.s. hereby declares that the JA-162PW, JA-162PW-GR, JA-162PW-AN product is in a compliance with the relevant Union harmonisation legislation: Directives No.: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU, if it is used as intended. The original of the conformity assessment can be found at www.jablotron.com Section Downloads.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.