Wireless combined motion and glass-break detector

type: 5PIRGBS2202OQ

The product is a wireless component of JABLOTRON system. It is used for the detection of movement detection in building interiors and for the detection of breakage of glass surfaces forming the building. It contains two independent sensors (it occupies 2 positions in the control panel). It uses a PIR sensor to detect the movement of people and a GBS detector to detect the breakage of glass surfaces. The GBS alarm is evaluated based on changes in air pressure and the characteristic sounds of glass breaking. The detector is designed to be installed by a trained technician with a valid Jablotron certificate.
The control panel must be equipped with a radio module to communicate the product with the system.

Installation

During the installation pay attention that there should be no obstacles in the detector’s view, such as:

• items that change temperature quickly (electric stove, gas appliances etc.)
• objects that move (e.g. waving curtains over the heating, robotic vacuum cleaner)
• no obstacles obstructing his view of the protected area
• moving pets

We do not recommend installing the detector:

• against windows or spotlights
• in places where air flows (ventilation, air conditioning, vents, leaky doors etc.)
• near air outlets, fans, or other sources of air pressure changes or intense sounds
• in a protected area where there are sources of vibration or shock

1. Open the detector cover by using the latch (5). Do not touch the PIR sensor inside (13) – it could be damaged.
2. Remove the locking screw (8). Release the PCB by pressing the latch (15).
3. The recommended installation height is 2.5 m above the floor.
4. Attach the rear housing part to the wall using screws (vertically, with the cover tab facing downwards).
5. Insert the PCB back into the rear housing part using the electronics latch (15) and screw the locking screw (8) back. Insert batteries to the battery holder (6).
6. Close the detector cover, snap into the cover latch (5) and secure with the locking screw.

   

Fig. 1: Description of external and internal parts of the product:
1 – Glass Break sensor; 2 – LED indicator; 3 – PIR sensor lens; 4 – locking screw hole; 5 – cover tab; 6 – battery holder; 7 – GBS sensor; 8 – GBS module locking screws; 9 – LED indicator; 10 – external tamper connector; 11 – serial number; 12 – tamper switch; 13 – PIR sensor; 14 – PCB; 15 – PCB latch;

Enrollment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specification

Power	2x lithium battery type CR123A (3 V/1.5 Ah) Please note: Batteries are not included.
Typical lifetime of batteries	approx. 3 years
Low battery voltage	<2.7 V
Quiescent current consumption	50 μA
Maximal current consumption	50 mA
Communication frequency	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	<25 mW
Recommended installation height	2.2–2.5 m
PIR detection angle/range	90 °/12 m
GBS detection angle/range	90 °/9 m
RF range	500 m (open area)
Detection type	acoustic
Dimensions	63 x 150 x 40 mm
Weight (w/o batteries)	135 g
Classification	Security grade 2/Environmental class II (according to EN 50131-1)
Environment	indoor general
Operating temperature range	-10 °C to +40 °C
Average operating humidity	75% RH, non-condensing
Certification body	Trezor Test (no. 3025)
Complies with	EN IEC 63000, EN 50130-4, EN 55032, EN IEC 62368-1, ETSI EN 300 220-1, -2, EN 50131-1, -2-2, -2-7-1, -5-3, -6
Can be operated according to	ERC/REC 70-03
Recommended screw	2 x ø 3.5 x 40 mm (countersunk head)

	JABLOTRON ALARMS a.s. hereby declares that the 5PIRGBS2202OQ product is in a compliance with the relevant Union harmonisation legislation: Directives No.: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU, if it is used as intended. The original of the conformity assessment can be found at www.jablotron.com Section Downloads.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.