Wireless PIR motion detector with a verification camera

The JA-160PC is wireless component of the JABLOTRON system. It serves for the detection of human movement in building interiors and visual alarm confirmation. The camera takes colour photos with a resolution of up to 640 x 480 pixels by detecting human movement while the system is set. The camera is equipped with a visible flash for taking photos in the dark. The detector should be installed by a trained technician with a valid certificate issued by an authorised distributor.

Installation

There should be no obstacles in front of the detector which might obstruct its view of the protected area:

• subjects, which quickly change temperature (e.g. heating appliances,)
• subjects, which move (e.g. curtains hanging above a radiator, robotic vacuum cleaners, pets)
• no obstacles in front of the detector which might obstruct its view of the protected area
• moving pets

It is not recommended to install the detector:

• opposite to windows or reflectors
• in places with over-intense air circulation (close to ventilators, heat sources, air conditioning outlets, unsealed doors, etc.)

Note: Installation in the corner of a room requires more attention during testing due to possible reflection of flash in the photographed scene (especially in the dark).

1. Open the detector cover by pushing the tab (4). Avoid touching the PIR sensor inside (15) – you could damage it.
2. Take out the PCB – it is held by a tab (9).
3. The recommended installation height is 2.5 m above the floor.
4. Screw the rear cover to the wall (vertically, cover tab down).
5. Re-insert the PCB and plug the connecting cable (6) into the connector on the PCB. Insert the batteries (mind the correct polarity).
6. There must be a JA-11xR radio module installed in the control panel7. Close the detector cover and test its functionality. In order to comply with norms, the cover tab (4) must be secured with the supplied screw.

   

Figure 1: Description of the internal and external parts of the product
1 – flash for illumination; 2 – camera lens; 3 – PIR detector lens; 4 – cover tab; 5 – camera module; 6 – connection cable; 7 – battery holder; 8 – red LED; 9 – PCB tab; 10 – yellow LED; 11 – yellow LED of Micro SD card; 12 – Micro SD memory card; 13 – mini USB connector; 14 – tamper contact; 15 – PIR sensor; 16 – production code;

Assignment to the system and settings

According to the type of control panel use recommended software or application – see control panel manual.

Technical specifications

Power	2 Alkaline battery type LR6 (AA) 1.5 V Batteries are not included
Typical lifetime of batteries	about 2 years
LowBatt state	2.4 V
Quiescent current consumption	70 µA
Maximum current consumption	800 mA
Communication frequency	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	< 25 mW
Communication range	approx. 300 m (unrestricted area)
Recommended installation height	2.5 m above the floor
Detection angle / detection coverage	55° / 12 m (basic lens)
Horizontal camera capture angle	43°
Range of the flash	max. 3 meters
Resolution of the camera	LQ 320 x 240; HQ 640 x 480 pixels
Photo size LQ / HQ (typically)	2-10 kB
Typical (LQ) photo transmission time to the control panel	up to 20 s (10 s)
Typical (HQ) photo transmission time to the control panel	up to 130 s (60 s)
Typical photo transfer time to the server	15 s / GPRS; 2 s / LAN
Operational environment	Indoor general
Operational temperature range	-10 °C to +40 °C
Average operational humidity	75% RH, without condensation
Dimensions	110 x 60 x 55 mm,
Weight (without batteries)	110 g
Classification	Security grade 2 / Environmental class II (according to EN 50131-1)
Certification body	Trezor Test s.r.o (no. 3025)
Complies with	EN 50131-1, EN 50131-2-2, EN 50131-5-3, EN 50131-6, ETSI EN 300 220-1,-2, EN 50130-4, EN 55032, EN 62368-1, EN IEC 63000
Can be operated according to	ERC/REC 70-03
Recommended screw	2 x ø 3.5 x 40 mm (countersunk head)

	JABLOTRON a.s. hereby declares that the product JA-160PC is in a compliance with the relevant Union harmonisation legislation: Directives No: 2014/30/EU, 2014/35/EU, 2014/53/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – Section Downloads.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.