Wireless multifunctional panic button

The device is a component of the JABLOTRON alarm system. It has four defined types of utilization – panic alarm button activated by hand, panic alarm button activated by foot or knee, detection of banknote removal or the removal of valuable documents, verification of the presence of a person with a variable timer. All of these options may be realized by utilizing the mounting platform, which is equipped with a tamper detector. Thanks to bi-directional communication, the device optically and acoustically signals confirmation of a successful action. The device utilizes wireless Jablotron communication protocol and is powered by two AAA batteries. The device should be installed by a trained technician with a valid certificate issued by an authorized distributor.

Installation

The Jablotron system must be equipped with a JA-11xR radio module in order to enable the functionality of the device. We recommend installing the panic alarm button onto the mounting platform (Fig. 1). The mounting platform allows for installation onto various types of surfaces and allows for the detection of tampering should the device be removed from the mounting platform. The device may be used without the mounting platform, however due to the fact that the tamper device is not present it is necessary to disable the device’s tamper sensor via recommended software. It must be noted that utilizing the device without its mounting platform results in non-conformity to Security Grade II classification.

1. Remove the panic button from its mounting platform by applying small force to the sides of the hinges, (3) see Fig.1, thus prying them apart. This action is best performed with the use of a flat tool.
2. Fix the mounting platform to the desired location with the use of four screws (10).
3. Remove the device’s backplate, this action may be performed by prying it away with the use of a flat-head screwdriver.
4. Follow the instructions stated in the control panel installation manual, insert both batteries into the product, close the device by replacing the backplate in its place and secure it in position with the use of a fixing screw.

Important: Place the panic button into the mounting platform by placing it between the hinges (3) so that both latches (7) are securely in place (Fig.1). Panic button si possible to put into mounting platfort by 2 ways. Orientation of the panic button is dependent on whether the customer wishes to utilize direct button activation by hand or by pressing the entire surface of the device so that the device may be operated by hand, knee or foot.

   

Fig. 1: Panic button and mounting platform – description of individual parts
1 – LED light guide; 2 – Replaceable banknote or document clip; 3 – hinges/hinges holder; 4 – button; 5 – switch of banknote/document; 6 – backplate locking screw; 7 – mounting platform latches; 8 – button activation plastic protrusion; 9 – sabotage magnet segment; 10 – fixing screw holes;

Enrolment to the system

Depending on the type of control panel, use the recommended software or application, see the control panel manual. Panic button can be enroled only to one control panel.

Technical specifications

Power	2 x alkaline battery, type AAA (LR03) 1.5 V/1.1Ah Important: Batteries are not included in the packaging (PS type C according to EN 50131-6)
Typical battery lifetime	approx. 3 years (if activated 3x per day)
Quiescent power consumption	20 μA
Maximum power consumption	40 mA
LowBatt	<2,3 V
Type of activation device	type V (min 5 N, max. 8 N) type C (min 5 N, max. 8 N) type K (min. 10 N, max. 15 N)
Communication frequency	868,1 MHz, Jablotron protocol
Maximum radio-frequency output (ERP)	5 mW
Communication range	aprox. 300 m (direct visibility)
Classification	Security grade 2/environmental class II (EN 50131-1)
Environment	Indoor general
Operational temperature range	-10 °C to +40 °C
Average operating humidity	75% RH, without condensing
Dimensions (with mounting platform)	66 x 22 x 122 mm
Weight (w/o batteries)	88 g
Operating conditions according to	ERC/REC 70-03
Certification body	Trezor Test s.r.o. (č. 3025)
In compliance with	ETSI EN 300 220-1,-2, EN 55032, EN 50130‑4, EN 62368-1, EN 62311, EN IEC 63000, EN 50131-1, EN 50131-3, EN 50131-5-3, EN 50131-6, CLC/TS 50131-11, EN 50134-2
Recommended screw	4 x ø 3,5 x 40 mm (cylindrical / half round head)

	JABLOTRON ALARMS a.s. hereby declares that the JA-156J detector is in a compliance with the relevant European Union harmonization legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – the Downloads section.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.