Wireless touchscreen keypad with reader RFID

type: 5KPAD2204RN

The keypad is a wireless component of the JABLOTRON system and is designed to be operated by touch. The keypad must be installed by a trained technician with a valid Jablotron certificate issued by an authorised distributor.

Fig. 1: front part / inner part / mounting pad
1 – touchscreen; 2 – button/system indicator; 3 – RFID reader; 4 – connection points of the terminal; 5 – serial number; 6 – tamper; 7 – rear part tab; 8 – connector for backup battery connection; 9 – backup battery; 10 – USB-C connector; 11 – locking mechanism; 12 – terminal;

Installation

Notes:

• Use a narrow flat screwdriver to turn the locking mechanism and release the tab.
• Connect only straight, stripped wires to the bus terminals (their ends only).
• The ideal height for good readability and control is at eye level. It is not recommended to mount at a height consistent with electrical switches (100–110 cm).

1. Remove the mounting pad (Fig. 3) of the keypad. If it cannot be removed easily, open the locking mechanism (11).
2. In the mounting pad, break out the blank of appropriate slot, pull the power cable through, and then screw the mounting pad of the keypad to the designated place, preferably on a solid base (wall). Select the installation height of the keypad with respect to the height of the users (eye height).
3. Insert the backup battery (9) to the keypad and plug it to an appropriate connector (8).
4. Connect the individual wires of the power cable to the terminal (12) as follows:
   1. Using a flathead screwdriver to press the plate on the top of the terminal block.
   2. Put a stripped wire into the appropriate terminal.
   3. Release the terminal.
   4. Test if the wire is correctly fixed with a gentle pull.
5. Screw on the mounting pad (vertically, rear part tab down). In order to properly detect tampering when the keypad is pulled off the surface, the holes (lower left and upper right) in the tear-out portion of the mounting pad have to be used.
6. Re-install the PCB and secure with locking mechanism (11).

Enrollment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specification

Type of control device (ACE)	type B Power supply
Backup battery	Li-Ion Polymer battery
Voltage/capacity	3.7 V/2500 mAh, recommended type BAT-3V7-2500
Maximum capacity	2520 mAh
Minimum capacity	2500 mAh
Typical backup battery lifetime	>48 hrs
LowBatt state	3.5 V
Maximum charging time to reach 80% of capacity	6–7 hrs
Nominal current consumption (display OFF)	58 mA
Maximal current consumption (display ON)	280 mA
Communication band	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	<25 mW
Communication range	approx. 200 m (open area)
RFID frequency	125 kHz
Maximum RFID mag. field strength	-5.4 dBμA/m (measured at 10 m)
Dimensions	95 x 183 x 30 mm
Weight (without battery)	258 g
Classification	Security grade 2/Environmental class I (According to EN 50131-1)
Environment	Indoor
Operating temperature range	0 °C to +40 °C
Average operational humidity	75% RH, w/o condensation
Certification body	Trezor Test s.r.o. (nr. 3025)
In compliance with	ETSI EN 300 220-1, -2, ETSI EN 300 330, EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000, EN 50131-1, -3, -5-3, -6
Can be operated according to	ERC REC 70-03
Recommended screw	4 x ø 3.5 x 40 mm (countersunk head)

	JABLOTRON ALARMS a.s. hereby declares that the 5KPAD2204RN is in a compliance with the relevant Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – Section Downloads.
	Note: Note: Although the product does not contain any harmful materials, do not dispose of it in the garbage, but take it to an e-waste collection point. For more information visit www.jablotron.com in the Downloads section.