Wireless access module with RFID and keypad

The access module is a component of the JABLOTRON system. Its modular architecture enables users to create a combination whose size of installation perfectly meets their needs. The device should be installed by a trained technician with a valid certificate issued by an authorised distributor.

Fig. 1: Description of external and internal parts of the product
1 – control segment; 2 – segment buttons; 3 – activation button with LED indicator; 4 – access module with RFID reader; 5 – tabs for module opening; 6 – cover screws; 7 – connector for control segment; 8 – production code; 9 – terminals; 10 – mini USB connector; 11 – battery holder; 12 – tamper contact;

Installation

1. Press the four tabs (5) on the sides (see fig. 1) one by one and release the module from the plastic base.
2. When installing more control segments, first remove the socket cover on the 1st segment.
3. Remove the transparent plastic cover from the segments (by levering on both sides of the segment near the buttons).
4. Always connect the segment wires to the connector of the previous segment and click them into each other (we recommend coiling the wires by turning the segment by 360° – this will prevent any possible damage to the wires between the plastic parts). Use this method to install all the required segments. Finally push the socket cover in.
5. Insert two 1.5 V alkaline AA batteries into the module.
6. Attach the base onto the selected place together with the segments using screws. If more segments are required fix those onto the wall using screws as well (use the number of screws required).
7. Connect the segment wires to the internal connector of the module (7).
8. Insert the module into the base.
9. Proceed according to the control panel installation manual. There must be a JA-110R radio module installed in the control panel with a reliable communication range to the access module. When batteries are inserted, the yellow LED (3) starts to light permanently which indicates that the module has not been enrolled to the system yet.

Assigment to the system

Depending on the type of control panel, use the recommended software or application, see the manual of the control panel.

Technical specifications

Power supply	2 x alkaline batteries, type: AA (LR6, 1.5 V/ 2.45 Ah) / Please note: Batteries are not included.
Typical battery lifetime	1–2 Years
Low Battery Threshold	<2 V
Quiescent current consumption	20 μA
Maximal current consumption	40 mA
Each additional control segment	2.5 mA
Communication range	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	15 mW
Communication range	cca 200 m (open area)
RFID frequency	125 kHz
Maximum RFID magnetic field strength	-5.4 dBμA/m (measured at 10 m dist.)
Dimensions	102 x 96 x 33 mm
Weight (without batteries)	160 g
Classification	Security grade 2/Environmental class II (EN 50131-1)
Environment	indoor general
Operating temperature range	-10 °C to +40 °C
Average operational humidity	75% RH, w/o condensation
Certification body	Trezor Test s.r.o. (no. 3025)
In compliance with	ETSI EN 300 220-1,-2, ETSI EN 300 330, EN 50130-4, EN 55032, EN 62368-1, EN IEC 63000, EN 50131-1, EN 50131-3, EN 50131-5-3, EN 50131-6
Operating conditions according to general authorization	ERC REC 70-03
Recommended screw	4 x ø 3.5 x 40 mm (countersunk head)

	JABLOTRON ALARMS a.s. hereby declares that the JA-153E, JA-153E-GR, JA-153E-AN, JA-153E-WH is in compliance with the relevant European Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU, when used as intended. The original of the conformity assessment can be found at www.jablotron.com – the Downloads section.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.