Wireless PIR motion detector

The product is a wireless device of the JABLOTRON system. It is used to detect the movement of people in interiors of buildings. Its guaranteed detection coverage is 90 ° horizontally and the detection range is 12 m. The detector should be installed by a trained technician with a valid certificate issued by an authorized distributor.

Installation

During the installation pay attention that there should be no obstacles in the detector’s view, such as:

• items that change temperature quickly (electric stove, gas appliances etc.)
• objects that move (e.g. waving curtains over the heating, robotic vacuum cleaner)
• no obstacles obstructing the view of the protected area
• moving pets

Installation procedure:

1. Open the detector cover by pressing the cover tab (4). Avoid touching the PIR sensor inside (9) – you could damage it.
2. Take out the PCB – it is held by a tab on a lower part of the plastic.
3. The recommended installation height is 2.2–2.5 m above the floor.
4. Screw the rear plastic to the selected location on the wall (vertically, cover latch down).
5. Insert the PCB back to the rear plastic by its latch and insert the battery to the battery holder (5).
6. Close the detector cover to the cover latch (4) and secure by locking screw.

Figure 1: Description of internal and external parts of the product
1 – LED indicator; 2 – PIR sensor lens; 3 – hole for locking screw; 4 – covert latch; 5 – battery holder; 6 – LED indicators; 7 – the JA-191PL external tamper contact; 8 – serial number; 9 – PIR sensor; 10 – tamper contact; 11 – PCB latch;

Enrolment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specifications

Power	1x Lithium battery type CR123A (3 V/1500 mAh) Please note: Battery is not included
Typical battery lifetime	up to 4 years depends on settings
Low battery voltage	<2,4 V
Quiescent current consumption	30 μA
Maximum current consumption	100 mA
Communication frequency	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	<25 mW
Communication band	approx. 300 m (open area)
Recommended installation height	2,2–2,5 m above the floor
Detection angle/detection coverage	90 °/12 m
Dimensions	62 x 110 x 40 mm
Weight (without battery)	90 g
Classification	security grade 2/environmental class II (according to EN 50131-1)
Environmental	indoor general
Operational temperature range	-10 °C to +40 °C
Average operational humidity	75% RH, non-condensation
Certification body	Trezor Test s.r.o. (no. 3025), KIWA Nederland B. V.
Complies with	EN 50131-1, EN 50131-2-2, EN 50131-5-3, EN 50131-6, ETSI EN 300 220 -2, EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000, T 031 (comply the requirements for installation in the corner of the room)
Can be operated according to	ERC REC 70-03
Recommended screw	2 x ø 3,5 x 40 mm (countersunk head)

	JABLOTRON a.s. hereby declares that the JA-152P, JA-152P-GR, JA-152P-AN product is in a compliance with the relevant Union harmonisation legislation: Directives No.: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU, if it is used as intended. The original of the conformity assessment can be found at http://www.jablotron.com section Downloads.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.