Wireless internal siren to an AC socket

Product is a wireless device of the JABLOTRON system. It is used for alarm indication inside a building with an option to distinguish the alarm type according to the type of signalling. Pressing the siren can silence an alarm (= confirmation of a person’s presence in the building). The siren is equipped with a backup battery for cases of AC dropouts. It has also got a built-in tamper sensor for the detection of disconnection from an electrical socket. The siren takes one position in the system, and it should be installed by a trained technician with a valid certificate issued by an authorized distributor.

Installation

The control panel has to be equipped with a JA-11xR radio module. The battery is already connected as default.

1. Plug the siren into the required electrical socket within RF range of the control panel. The control button (1) lights with a yellow colour indicating that the siren is ready to be enrolled.
2. Proceed by following the control panel installation manual.
3. Press the control button (1). The yellow LED goes off and the siren is enrolled to the required position.
4. Follow the instructions below.

Warning: In case of unplugging the siren from the electricity, the siren is powered by the backup battery and is able to work for at least 24 hrs. When the backup battery voltage reaches critical level, the battery is disconnected to protect it against damage; the siren is out of service from this moment.

Figure 1: Description of external and internal parts of the product
1 – transparent control button; 2 – backup battery; 3 – battery connector; 4 – rear tamper sensor; 5 – front cover screws;

Assignment to the system

Depending on the type of control panel, use the recommended software or application, see the manual of the control panel.

Technical specifications

Power	90–253 V AC, 50–60 Hz; protection class II
Quiescent current consumption	4 mA
Maximum current consumption	13 mA
Backup battery/lifetime	3.2 V, 400 mAh (LiFePo4CR2)/3 years
– minimum voltage when loaded	3.0 V
– maximum voltage when unloaded	3.6 V
– low battery voltage	2.6 V
– maximum current	308 mA
Power supply	type A (according to 50131-6)
Communication band	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency power (ERP)	<25 mW
RF range	approx. 300 m (open area)
Backup power supply	type Y/24h backup
Alarm acoustic level	100 dB/1 m
Dimensions (without the electric plug)	90 x 70 x 45 mm
Weight	150 g
Classification	Grade 2/Environmental Class II (According to EN 50131-1)
Operational environment	indoor general
Operational temperature range	-10 °C to +40 °C
Average operational humidity	75% RH, without condensation
Certification body	Trezor Test s.r.o. (no. 3025)
Degree of protection	IP40 according to EN 60529
Mechanical impact protection	IK08 according to EN 50102
Complies with	EN 50131-1, EN 50131-4, EN 50131-5-3, EN 50131-6, ETSI EN 300 220-1,-2, EN 50130-4, EN 55032, EN 62368-1, EN IEC 63000, EN IEC 62311
Can be operated according to	ERC/REC 70-03

	JABLOTRON a.s. hereby declares that the JA-152A is in compliance with the relevant European Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU, when used as intended. The original of the conformity assessment can be found at www.jablotron.com – the Downloads section.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.