Wireless PIR motion detector with basic pet immunity

The JA-150P PET is a wireless device of the JABLOTRON system. It is used to detect movement of persons in interiors of buildings. Unlike the standard PIR motion detectors from the JABLOTRON series, this detector has a modified detection characteristic and it is equipped with basic pet immunity. The detector eliminates the effect of the movement of small animals on the floor (animals with a weight of up to approx. 25 kg and a maximum height of 40 cm). It is not suitable for guarding areas where animals can move freely at height! The detector has a pulse reaction and it takes one position in the system. The detector should be installed by a trained technician with a valid certificate issued by an authorized distributor.

Instalation

1. Open the detector cover by pressing the cover tab (5). Avoid touching the PIR sensor inside (10) – you could damage it.
2. Take out the PCB – it is held by a tab (3).
3. Punch through the holes for screws in the plastic base and attach it to the wall. The recommended detector installation height is 2 m above the floor, maximum height 2.2 m.
4. Insert the PCB back and put both batteries into the holder. Proceed by following the control panel installation manual.
5. Close the detector cover and test the detector’s function.

      

Fig. 1: Opening the detector and description of external and internal parts of the product
1 – holes for installing on a flat wall; 2 – holes for installing at an angle (in a corner); 3 – PCB tab; 4 – holes for installing at an angle (in a corner); 5 – cover tab; 6 – red LED diode – activation; 7 – battery holder; 8 – production code; 9 – tamper; 10 – PIR sensor;

Assigment to the system

Depending on the type of control panel, use the recommended software or application, see the manual of the control panel.

Technical specifications

Power	2x Alkaline battery, type LR6 (AA) 1.5 V/2.4 Ah Please note: Batteries are not included.
Typical lifetime of batteries	about 2 years (the longest lifetime is achieved in Smartwatch mode)
LowBatt	<2.5 V
Quiescent current consumption	25 μA
Maximal current consumption	50 mA
Communication frequency	868.1 MHz, JABLOTRON protocol
Maximum radio-frequency output (ERP)	25 mW
Communication range	approx. 300 m (unrestricted area)
Recommended installation height	2 m above the floor
Detection angle/detection coverage	90 °/12 m
Pet immunity (angle/coverage)	90 °/up to 7 m
Dimensions	60 x 95 x 55 mm
Weight (without batteries)	125 g
Classification	Grade 2/II. indoor general (According to EN 50131-1)
Operational environment	Indoor general
Operating temperature range	-10 °C to +40 °C
Average operating humidity	75 % RH, without condensation
Certification body	Trezor Test s.r.o. (no. 3025), Telefication B.V.
Complies with	ETSI EN 300 220-1,-2, EN 50130-4, EN 62368-1, EN IEC 63000, EN 55032, EN 50131-1, -2-2, -5-3, -6, T 031
Operating conditions	according to general authorization ERC REC 70-03
Recommended screw	2 x ø 3.5 x 40 mm (countersunk head)

	JABLOTRON ALARMS a.s. hereby declares that the JA-150P PET is in compliance with the relevant European Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU, when used as intended. The original of the conformity assessment can be found at www.jablotron.com – the Downloads section.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.