Bus combined PIR motion detector with photoverification camera

Type: 1PIRCAM2201MP

This device is a component of the JABLOTRON system. It serves for the detection of human movement in building interiors and visual alarm confirmation. The camera takes colour photos with a resolution of up to 640×480 pixels. The camera is equipped with a visible flash for taking photos in the dark. The images are saved in the internal memory of the detector and then they are forwarded to the control panel and from the control panel they can be sent to MyJABLOTRON or ARC. The detector can also take a picture by request. The detector takes one position in the system and should be installed by a trained technician with a valid certificate issued by an authorised distributor.

Instalace

Always switch the system power off before connecting the detector to the system bus.

• Open the detector cover (by pushing the cover tab (6). Avoid touching the PIR sensor inside (13) – you could damage it.
• Remove the locking screw (9) Take out the PCB – it is held by a tab (14).
• The recommended installation height is 2.5 m above the floor.
• Pull the bus cable through the rear plastic and screw on the rear plastic (vertically, cover latch down).
• Re-insert the PCB and secure it with a tab (14) and a locking screw (9) and connect the BUS connector (8).
• Proceed according to the control panel installation manual.

   

Figure 1: Description of external and internal parts of the product
1 – flash for illumination; 2 – camera lens; 3 – LED indicator; 4 – PIR detector lens; 5 – locking screw; 6 – cover tab; 7 – External bus connector of tamper contact; 8 – BUS; 9 – camera module locking screw; 10 – LED indicators; 11 – serial number; 12 – tamper contact; 13 – PIR sensor; 14 – PCB tab;

Enrolment to the system

Depending on the type of control panel, use the recommended software or application or the manual of the control panel.

Technical specifications

Power	from the control panel bus 12 V DC (8–15 V)
Quiescent current consumption	5 mA
Maximum current consumption	250 mA
Recommended installation height	2.5 m above the floor
PIR Detection angle/detection coverage	90 °/12 m
Camera capture angle	90 °
Range of the flash	max. 3 m
Resolution of the camera	LQ 320 x 240; HQ 640 x 480 pixels
Photo size LQ/HQ	5–20 kB/5–64 kB
Typical (LQ) photo transmission time to the control panel	up to 20 s (10 s)
Typical (HQ) photo transmission time to the control panel	up to 130 s (60 s)
Typical photo transfer time to the server	15 s/GPRS; 2 s/LAN
Dimensions, weight	150 x 65 x 44 mm, 125 g
Operational temperature range	-10 °C to +40 °C
Operational environment	Indoor general
Average operational humidity	75% RH, without condensation
Classification	Security grade 2/Environmental class II (EN 50131-1)
Certification body	Trezor Test no. 3025
Complies with	EN 50131-1, EN 50131-2-2, EN 50130-4, EN 55032, EN IEC 63000
Recommended screw	2 x ø 3.5 x 40 mm (countersunk head)

	JABLOTRON ALARMS a.s. hereby declares that the 1PIRCAM2201MP is in compliance with the relevant European Union harmonisation legislation: Directives No: 2014/30/EU, 2011/65/EU, when used as intended. The original of the conformity assessment can be found at www.jablotron.com – the Downloads section.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.