Setting the properties

To set the properties, use the F-Link program, select the Devices tab. At the product/reader position, click the Enter prompt in the Internal settings column.

The signalization shows the status of a function assigned to the segment. Red LED indicates an armed/turned on PG. Green LED indicates a disarmed section/turned off PG. Yellow LED indicates a fault by permanent light.

Behaviour of optical indication may be set in the F-Link software by selecting from the following options.

The asterisk symbol ^* signifies the factory default setting.

LED function

None / Indicates section^* / Indicates PG / PG indicates inversely

Acoustic indication of selected sections

The asterisk symbol * signifies the factory default setting.

Alarm: ^*On/Off: Signalizes ongoing alarm in an assigned section.

Entrance delay: ^*On/Off: Signalizes entry delay in a section to which it is assigned.

Exit delay: ^*On/Off: Signalizes exit delay in a section to which it is assigned.

Exit delay when partially set: On/^*Off

Segment status change: Reader signalized acoustic section in which is assigned.

Mute: On/^*Off: If ON is selected, reader will not signalize exit and alarm.

Properties and indication

Indicates permanently – LED 1 or LED 2 lights up permanently/signals the status of the PG/section. The reader displays the status permanently. In case of a power failure, it behaves according to the By status change option.

After valid authorization – applying a card/chip, the signalling is activated and the LED displays the status of the PG/section (selected PG in the Authorization action setting, if selected) for 8 seconds.

After valid authorisation in acc. with EN50131-1 – by reading a card of a user that is defined within the system, the current status of a PG/section is displayed for 4 seconds (selected PG in the Authorization action setting, if selected).

Authorised action

Authorisation triggers an entrance delay: On/Off*: If the section, to which the reader is assigned, is in an armed state, authorisation by the means of reading a card induces an entry delay. Simultaneously it activates a PG.

The reader can be used to control PGs that have the Impulse or Change function set. These functions can be set in the internal settings of the F-link.

Technical specifications

Power	From the control panel bus, 12 V DC (8–15 V)
Quiescent current consumption	12 mA
Maximal current consumption	60 mA
Type of control device	B
Operating RFID frequency	13,56 MHz
Maximum RFID magnetic field strength	10,37 dBuA/m (3 m)
Compatible RFID cards	NFC, Mifare® Classic, Mifare® DESFire® 4, 7 Byte UID
Dimensions	46 x 151,5 x 25 mm
Weight	185 g
Cable length	3,0 m
Operating temperature range	-25 °C to +60 °C
Relative humidity	75% Without condensation
Environment according to EN 50131-1	IV. indoor general
Classification	grade 2 according to EN 50131-1, EN 50131-3
Additionally in compliance with	ETSI EN 300 330, EN 50130-4, EN 55032, EN 62368-1, EN IEC 63000
Recommended screw	3 x ø 3,5 x 40 mm (flat head)

MIFARE® is a registered trademark owned by NXP B.V. There is no affiliation between NXP B.V. and JABLOTRON a.s.

	JABLOTRON a.s. hereby declares that the product 1KPAD2318LU is in compliance with the relevant Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – Section Downloads.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.