Bus outdoor access module with RFID and NFC reader

Type: 1READER1702OS_TF

This product is a component of the JABLOTRON system. The outdoor card reader contains 2 reading zones and allows the simultaneous combination of 125 kHz (RFID) and 13.56 MHz (MIFARE® Classic) frequencies. Card reader can be used to activate PG outputs for example to control access (door lock). It has only reading zone and an optical status indication. The product is intended for installation by a trained technician with a valid Jablotron certificate.

Installation

When connecting the module to the bus, always switch the power off.

1. Install the mounting pad with 2 screws in the prepared place.
2. Pull the cable from the reader through the hole in the mounting pad.
3. Align the reader on the top edge of the mounting pad (Figure 2) and click it in.
4. Then secure the card reader with the locking screw (4).
5. Connect the bus cable to the bus terminals via a JA-110Z-x terminal module and a JA-19xPL installation box.

• If the reader is located outside the secure area, use the JA-110T bus isolator.
• To mount the reader on the KU68 installation box, use the WRE-KU68 WH (BK) adapter.
• To mount the reader with the cable duct, use the WRE-SC-WH (BK) adapter.

Figure 1: Description of external parts of the product
1 – LED indicator; 2 – 125 kHz reading zone; 3 – 13,56 MHz reading zone; 4 – locking screw;

Figure 2: Reader installation

Enrolment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specification

Type of control device	A
Power	from control panel digital bus (8…15 V)
Current consumption in standby mode	50 mA
Current consumption for cable selection	110 mA
IP cover conformance according to EN 60529	IP55
Mechanical strength according to EN 50102	IK08
RFID frequency	125 kHz
Maximum RFID magnetic field strength	-22.9 dBμA/m
MIFARE® frequency	13.56 MHz
Maximum MIFARE® magnetic field strength	-2.7 dBμA/m
RFID cards	JABLOTRON 100
MIFARE® cards	MIFARE® Classic
Dimensions	96 x 67 x 19 mm
Weight	140 g
Cable length	2.0 m +/- 5 %
Operating temperature range	-25 °C to +70 °C
Average operational humidity	5 to 95 % RH, non-condensation
Operational environment	EN 50131-1 IV. outdoor general
Classification	security grade 2/environmental class IV
Certification body	Trezor Test s.r.o. (nr. 3025) Telefication B.V.
according to	EN 50131-1, EN 50131-3
In compliance with	ETSI EN 300 330, EN 55024, ETSI EN 301 489-1, -3, EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000
Can be operated according to	ERC REC 70-03
Recommended screw	2 x ø 3.5 x 40 mm (countersunk head)

MIFARE® is registered trademark, owned by NXP B.V. There is no affiliation between NXP B.V. and JABLOTRON a.s.

	JABLOTRON a.s. hereby declares that the 1READER1702OS_TF is in a compliance with the relevant European Union harmonisation legislation: Directives No: 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – the Downloads Section.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.