Bus four-segment keypad with display and RFID reader

Type: 1KPAD2201LU

The keypad is a component of the JABLOTRON system. It serves for the controlling and current system status indication. It is equipped with four segments. Their descriptions are displayed on the LCD display. The device should be installed by a trained technician with a valid certificate issued by an authorised distributor. The keypad is compatible with following control panels JA-102K, JA-103K and JA-107K. The keypad comprises 4 segments (1), LCD display (2), keypad and RFID card/tag reader (4). The tilting cover (5) can be removed if the user prefers permanent access.

Installation

Always switch the power off before connecting the detector to the bus.

1. On the underside of the keypad, turn the locking mechanism (9) anticlockwise 90° until the groove points to the symbol . Then use a screwdriver to release the tab (10) while sliding the keypad up. The keypad can then be easily removed from the mounting pad. (If the mounting pad is not screwed on, use the same procedure, just slide the mounting pad downwards against the keypad).
2. Remove the mounting pad (rear part) of the keypad.
3. In the rear part, break out the cover on the corresponding place, push the bus cable through the plastic base and attach it to the selected place.
4. Connect all the bus cable wires to the terminal (6) as follows:
   1. using a flat screwdriver to press upper side of the terminal,
   2. put the stripped wire into to correct terminal,
   3. release the terminal,
   4. by a gentle pulling of the wire test if it´s correctly fixed.

+U – red; positive power supply pole; A – yellow; data wire A; B – green; data wire B; GND – black; negative power supply pole

Note: Connect only straight, stripped wires to the bus terminals (their ends only).

5. First attach the bottom edge of the keypad to the mounting pad (rear part) of housing (align the bottom sides). Then slide the keypad downwards, until you hear the click of the tab (10). This will secure the keypad against falling out of the installation pad. Then turn the locking mechanism (9) clockwise 90° to the position where the groove points to the symbol ). This locks the keypad in place and engages the tamper contact.
6. Power the system on.

      

Fig. 1: Description of the external and internal parts of product
1 – control buttons; 2 – LCD display; 3 – system indicator / button; 4 – keypad with RFID reader; 5 – cover; 6 – connection points of the bus terminal; 7 – serial number; 8 – tamper contacts; 9 – locking mechanism; 10 – tab

Enrollment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specifications

Type of control device	B
Power	from control panel bus, 12 V DC (8–15 V)
Current consumption in standby mode	18 mA
Current consumption for cable selection	100 mA
RFID frequency	125 kHz
Maximum RFID magnetic field strength	-5.4 dBμA/m (measured at 10 m)
Dimensions	110 x 136 x 33 mm
Weight	285 g
Environment	indoor general
Classification	Security grade 2/Environmental class II (According to EN 50131-1)
Operating temperature range	-10 °C to +40 °C
Average operational humidity	75% RH, w/o condensation
Certification body	Trezor Test s.r.o. (nr. 3025)
In compliance with	ETSI EN 300 330, EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000, EN 50131-1, EN 50131-3
Can be operated according to	ERC REC 70-03
Recommended screw	4 x ø 3.5 x 40 mm (half-round head)

	JABLOTRON a.s. hereby declares that the 1KPAD2201LU is in a compliance with the relevant Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – Section Downloads.
	Note: Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please return the product to the dealer or contact your local authority for further details of your nearest designated collection point.