Bus touchscreen keypad with RFID reader

type: 1KPAD2203RN

The keypad is a component of the JABLOTRON system and is designed to be operated by touch. The keypad must be installed by a trained technician with a valid Jablotron certificate issued by an authorised distributor.

Fig. 1: outer part / inner part / mounting pad
1 – touchscreen; 2 – button/system indicator; 3 – RFID reader – reading area; 4 – connection points of the bus terminal; 5 – serial number; 6 – tamper contacts; 7 – USB-C connector; 8 – locking mechanism; 9 – rear part tab; 10 – Bus terminal;

Installation

Always switch the power off before connecting the keypad to the BUS.

Notes:

• Use a narrow flat screwdriver to turn the locking mechanism and release the tab.
• Connect only straight, stripped wires to the bus terminals (their ends only).
• The ideal height for good readability and control is at eye level. It is not recommended to mount at a height consistent with electrical switches (100–110 cm).

1. Remove the mounting pad (Fig. 3) of the keypad. If it cannot be removed easily, open the locking mechanism (8).
2. In the mounting pad, break out the blank of appropriate slot, pull the bus cable through, and then screw the mounting pad of the keypad to the designated place, preferably on a solid base (wall). Select the installation height of the keypad with respect to the height of the users (eye height).
3. Connect the individual wires of the bus cable to the bus terminal (10) as follows:
   1. Using a flathead screwdriver to press the plate on the top of the terminal block.
   2. Put a stripped wire into the appropriate terminal.
   3. Release the terminal.
   4. Test if the wire is correctly fixed with a gentle pull.
4. Screw on the mounting pad (vertically, rear part tab down). In order to properly detect tampering when the keypad is pulled off the surface, the holes (lower left and upper right) in the tear-out portion of the mounting pad have to be used.
5. Reinstall the electronics and secure the PCB with the locking mechanism (8).

Enrollment to the system and settings

Depending on the type of control panel, use the recommended software or application, see the control panel manual.

Technical specification

Type of control device	type B
Power	from control panel bus 12 V DC (8–15 V)
Current power consumption for backup chose	40 mA
Quiescent current consumption (display OFF)	85 mA
Maximal current consumption (for cable selection)	250 mA
RFID frequency	125 kHz
Maximum RFID magnetic field strength	-5.4 dBμA/m (measured at 10 m)
Dimensions	95 x 183 x 30 mm
Weight	248 g
Classification	Security grade 2/Environmental class II (according to EN 50131-1)
Environment	indoor general
Operating temperature range	-10 °C to +40 °C
Average operational humidity	75% RH, non-condensation
Certification body	Trezor Test s.r.o. (no. 3025)
In compliance with	ETSI EN 300 330, EN 50130-4, EN 55032, EN IEC 62368-1, EN IEC 63000, EN 50131-1, EN 50131-3
Can be operated according to	ERC REC 70-03
Recommended screw	4 x ø 3.5 x 40 mm (half-round head)

	JABLOTRON ALARMS a.s. hereby declares that the 1KPAD2203RN is in a compliance with the relevant Union harmonisation legislation: Directives No: 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The original of the conformity assessment can be found at www.jablotron.com – Section Downloads.
	Note: Although the product does not contain any harmful materials, do not dispose of it in the garbage, but take it to an e-waste collection point. For more information visit www.jablotron.com in the Downloads section.